AccScience Publishing / ESAM / Online First / DOI: 10.36922/ESAM025170009
Submit to ESAM
Cite this article
12
Download
89
Views
Journal Browser
Volume | Year
Issue
Search
Forthcoming Issue
Current Issue
View All
News and Announcements
View All
ORIGINAL RESEARCH ARTICLE

Mechanical properties and energy absorption capability improvement of Ti-6Al-4V porous materials through porous structure design optimization

Yu-Yao Chan1 ,  Yi Chao1 ,  Che-Nan Kuo1*
Show Less
1 Department of Materials and Optoelectronic Science, National Sun Yat-sen University, Kaohsiung, Taiwan, Republic of China
ESAM 2025, 1(2), 025170009 https://doi.org/10.36922/ESAM025170009
Received: 21 April 2025 | Revised: 8 May 2025 | Accepted: 20 May 2025 | Published online: 17 June 2025
© 2025 by the Author(s). This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution 4.0 International License ( https://creativecommons.org/licenses/by/4.0/ )
Download PDF
Cite
XML
Abstract

The structural materials, which exhibit high toughness and high strain energy absorption, can be used in impact-resistant applications such as bulletproof vests, automobiles, and aerospace. Numerous studies indicate that functional gradient materials, which contain non-uniform density, exhibit excellent performance in energy absorption. During the compression test, the struts of the gradient porosity materials collapsed layer by layer, and this phenomenon optimizes the energy absorption capability of the materials. Furthermore, the collapse region or direction can be predicted and controlled by the design of the gradient porosity materials. In addition to the above concepts, this research also improves its energy absorption capacity through the following two strategies: (1) Chamfering the node of the porous structure to avoid the stress concentration, and (2) optimizing the angle between the struts of the porous material to enhance the ductility of the material. To fabricate the complicated gradient porosity structure, the structural materials were printed using the selective laser melting process with Ti-6Al-4V ELI alloys. Through the experiments conducted in this study, the structural strength was enhanced by up to 28% through structure design, and the energy absorption was improved by 19% compared to the gyroid structure, which has been reported to exhibit good energy absorption capabilities.

Keywords
Energy absorption
Ti-6Al-4V
Chamfering design
Selective laser melting
Lattice structure design
Funding
The authors gratefully acknowledge the sponsorship support from the National Science and Technology Council of Taiwan, ROC, under project no. NSTC 112- 2221-E-110-019.
Conflict of interest
Che-Nan Kuo is an Editorial Board Member of this journal but was not in any way involved in the editorial and peer-review process conducted for this paper, directly or indirectly. Separately, other authors declared that they have no known competing financial interests or personal relationships that could have influenced the work reported in this paper.
References
  1. Simonelli M, Tse YY, Tuck C. The formation of α+ β microstructure in as-fabricated selective laser melting of Ti-6Al-4V. J Mater Res. 2014;29(17):2028-2035. doi: 10.1557/jmr.2014.166

 

  1. Cui C, Hu B, Zhao L, Liu S. Titanium alloy production technology, market prospects and industry development. Mater Design. 2011;32(3):1684-1691. doi: 10.1016/j.matdes.2010.09.011

 

  1. Liu S, Shin YC. Additive manufacturing of Ti6Al4V alloy: A review. Mater Design. 2018;164:107552. doi: 10.1016/j.matdes.2018.107552

 

  1. Donachie MJ. Titanium: A Technical Guide. 2nd ed. Netherlands: ASM International; 2000. doi: 10.31399/asm.tb.ttg2.9781627082693

 

  1. Li Y, Feng Z, Hao L, et al. A review on functionally graded materials and structures via additive manufacturing: From multi‐scale design to versatile functional properties. Adv Mater Technol. 2020;5(6):1900981. doi: 10.1002/admt.201900981

 

  1. Allen J. An investigation into the comparative costs of additive manufacture vs. Machine from solid for aero engine parts. Cost Eff Manuf via Net-Shape Process. 2006;17:1-17.

 

  1. O’Leary R, Setchi R, Prickett P, Hankins G, Jones N. An investigation into the recycling of Ti-6Al-4V powder used within SLM to improve sustainability. Impact J Innov Impact. 2016;8(2):377.

 

  1. Kas M, Yilmaz O. Radially graded porous structure design for laser powder bed fusion additive manufacturing of Ti-6Al-4V alloy. J Mater Process Technol. 2021;296:117186. doi: 10.1016/j.jmatprotec.2021.117186

 

  1. Zhang W, Xu J. Advanced lightweight materials for automobiles: A review. Mater Design. 2022;221:110994. doi: 10.1016/j.matdes.2022.110994

 

  1. Lv X, Xiao Z, Fang J, Li Q, Lei F, Sun G. On safety design of vehicle for protection of vulnerable road users: A review. Thin-Walled Struct. 2023;182:109990. doi: 10.1016/j.tws.2022.109990

 

  1. Huang R, Riddle M, Graziano D, et al. Energy and emissions saving potential of additive manufacturing: The case of lightweight aircraft components. J Clean Prod. 2016;135:1559-1570. doi: 10.1016/j.jclepro.2015.04.109

 

  1. Uhlmann E, Kersting R, Klein TB, Cruz MF, Borille AV. Additive manufacturing of titanium alloy for aircraft components. Procedia Cirp. 2015;35:55-60. doi: 10.1016/j.procir.2015.08.061

 

  1. Zochowski P, Bajkowski M, Grygoruk R, et al. Ballistic impact resistance of bulletproof vest inserts containing printed titanium structures. Metals. 2021;11(2):225. doi: 10.3390/met11020225

 

  1. Brennan-Craddock J, Brackett D, Wildman R, Hague R. The design of impact absorbing structures for additive manufacture. J Phys Conf Ser. 2012;382:012042. doi: 10.1088/1742-6596/382/1/012042

 

  1. Pan C, Han Y, Lu J. Design and optimization of lattice structures: A review. Appl Sci. 2020;10(18):63-74. doi: 10.3390/app10186374

 

  1. Park KM, Min KS, Roh YS. Design optimization of lattice structures under compression: Study of unit cell types and Cell arrangements. Materials. 2022;15:97. doi: 10.3390/ma15010097

 

  1. Thompson SM, Bian L, Shamsaei N, Yadollahi A. An overview of direct laser deposition for additive manufacturing; part I: Transport phenomena, modeling and diagnostics. Addit Manuf. 2015;8:36-62. doi: 10.1016/j.addma.2015.07.001

 

  1. Yap CY, Chua CK, Dong ZL, et al. Review of selective laser melting: Materials and applications. Appl Phys Rev. 2015;2(4):041101. doi: 10.1063/1.4935926

 

  1. Khorasani A, Gibson I, Awan US, Ghaderi A. The effect of SLM process parameters on density, hardness, tensile strength and surface quality of Ti-6Al-4V. Addit Manuf. 2019;25:176-186. doi: 10.1016/j.addma.2018.09.002

 

  1. Shifeng W, Shuai L, Qingsong W, Yan C, Sheng Z, Yusheng S. Effect of molten pool boundaries on the mechanical properties of selective laser melting parts. J Mater Process Technol. 2014;214(11):2660-2667. doi: 10.1016/j.jmatprotec.2014.06.002

 

  1. Ansari MJ, Nguyen DS, Park HS. Investigation of SLM process in terms of temperature distribution and melting pool size: Modeling and experimental approaches. Materials. 2019;12(8):1272. doi: 10.3390/ma12081272

 

  1. Seetoh IP, Liu X, Markandan K, Zhen L, Lai CQ. Strength and energy absorption characteristics of Ti6Al4V auxetic 3D anti-tetrachiral metamaterials. Mech Mater. 2021;156:103811. doi: 10.1016/j.mechmat.2021.103811

 

  1. Choy SY, Sun CN, Sin WJ, et al. Superior energy absorption of continuously graded microlattices by electron beam additive manufacturing. Virtual Phys Prototyp. 2021;16(1):1-15. doi: 10.1080/17452759.2020.1868656

 

  1. Mahamood RM, Akinlabi ET, Owolabi MG, Abdulrahman KO. Advanced manufacture of compositionally graded composite materials: An overview. In: Hierarchical Composite Materials: Materials, Manufacturing, Engineering. Berlin, Boston: De Gruyter; 2019. p. 41-54. doi: 10.1515/9783110545104-003

 

  1. Evans AG, He MY, Deshpande VS, Hutchinson JW, Jacobsen AJ, Carter WB. Concepts for enhanced energy absorption using hollow micro-lattices. Int J Impact Eng. 2010;37:947-959. doi: 10.1016/j.ijimpeng.2010.03.007

 

  1. Liu F, Zhang DZ, Zhang P, Zhao M, Jafar S. Mechanical properties of optimized diamond lattice structure for bone scaffolds fabricated via selective laser melting. Materials. 2018;11:374. doi: 10.3390/ma11030374

 

  1. Zhao M, Zhang DZ, Liu F, Li Z, Ma Z, Ren Z. Mechanical and energy absorption characteristics of additively manufactured functionally graded sheet lattice structures with minimal surfaces. Int J Mech Sci. 2020;167:105262. doi: 10.1016/j.ijmecsci.2019.105262

 

  1. Sun Q, Sun J, Guo K, Wang L. Compressive mechanical properties and energy absorption characteristics of SLM fabricated Ti6Al4V triply periodic minimal surface cellular structures. Mech Mater. 2022;166:104241. doi: 10.1016/j.mechmat.2022.104241

 

  1. Zhao X, Li Z, Zou Y, Zhao X. Compressive characteristics and energy absorption capacity of automobile energy-absorbing box with filled porous TPMS structures. Appl Sci. 2024;14(9):3790. doi: 10.3390/app14093790

 

  1. Li Z, Zhao R, Chen X, Jiao Y, Chen Z. Design approach for tuning the hybrid region of 3D-printed heterogeneous structures: Modulating mechanics and energy absorption capacity. ACS Appl Mater Interfaces. 2023;15(6):7686-7699. doi: 10.1021/acsami.2c17753

 

  1. Dong JH, Wang YJ, Jin FN, Fan HL. Crushing behaviors of buckling-induced metallic meta-lattice structures. Def Technol. 2022;18(8):1301-1310. doi: 10.1016/j.dt.2021.07.014

 

  1. Obadimu SO, Kourousis KI. Compressive behaviour of additively manufactured lattice structures: A review. Aerospace. 2021;8(8):207. doi: 10.3390/aerospace8080207

 

  1. Li Y, Wang XS, Meng XK. Buckling behavior of metal film/ substrate structure under pure bending. Appl Phys Lett. 2008;92(13):131902. doi: 10.1063/1.2897035

 

  1. Zhao S, Li SJ, Hou WT, Hao YL, Yang R, Misr RDK. The influence of cell morphology on the compressive fatigue behavior of Ti-6Al-4V meshes fabricated by electron beam melting. J Mech Behav Biomed Mater. 2016;59:251-264. doi: 10.1016/j.jmbbm.2016.01.034

 

  1. Li D, Liao W, Dai N, Xie YM. Comparison of mechanical properties and energy absorption of sheet-based and strut-based gyroid cellular structures with graded densities. Materials. 2019;12(13):2183. doi: 10.3390/ma12132183

 

  1. Yang E, Leary M, Lozanovski B, et al. Effect of geometry on the mechanical properties of Ti-6Al-4V Gyroid structures fabricated via SLM: A numerical study. Mater Design. 2019;184:108165. doi: 10.1016/j.matdes.2019.108165

 

  1. Choy SY, Sun CN, Leong KF, Wei J. Compressive properties of Ti-6Al-4V lattice structures fabricated by selective laser melting: Design, orientation and density. Addit Manuf. 2017;16:213-224. doi: 10.1016/j.addma.2017.06.012

 

  1. Jenkins SNM. Mechanical Properties and Structural Evaluation of Diamond Structure Ti6Al4V Lattices Made by Electron Beam Melting. England: University of Sheffield; 2017.

 

  1. Kurdi A, Basak AK. Micro-mechanical behaviour of selective laser melted Ti6Al4V under compression. Mater Sci Eng A. 2021;826:141975. doi: 10.1016/j.msea.2021.141975

 

  1. Zhao M, Liu F, Fu G, Zhang DZ, Zhang T, Zhou H. Improved mechanical properties and energy absorption of BCC lattice structures with triply periodic minimal surfaces fabricated by SLM. Materials. 2018;11(12):2411. doi: 10.3390/ma11122411

 

  1. Wang YP, Kuo CN. Research on energy absorption of gradient porosity structural materials. Mater Today Proc. 2022;70:578-582. doi: 10.1016/j.matpr.2022.09.594

 

  1. Kuo CN, Wang YP, Chua CK. Effect of electropolishing on mechanical property enhancement of Ti6Al4V porous materials fabricated by selective laser melting. Virtual Phys Prototyp. 2022;17(4):919-931. doi: 10.1080/17452759.2022.2090383

 

Next article in this issue
Share
Back to top
Engineering Science in Additive Manufacturing, Published by AccScience Publishing
We use cookies on our website to ensure you get the best experience.
Read more about our cookies here
Accept